You Must Know These about Proper Crimping Techniques

For crimping, this is correct. To ensure a long-lasting connection, use proper crimping procedures and a Fiber Crimping Machine throughout the fiber termination operation. After all termination processes have been completed, the cable can be tugged without coming loose from the connection. Specify the maximum draw force for each fiber optic cable assembly industry specification, as well as any needs from your customer.

When correctly crimped, the cable assembly is strong enough to resist a decent amount of pulling throughout the final phases of manufacture and installation. Even after installation, the cable assembly may have to tolerate some mechanical stresses. A suitable fiber crimping machine ensures that force is applied to the connection rather than the delicate glass fiber.

Crimping, a small but important step in the manufacturing process, typically strengthens the cable assembly and protects the fiber. Proper crimping procedures and Fiber Polishing Machine assist in ensuring that the optical connection is maintained, which has a direct influence on dependability and performance over time.

Advice on Best-Practice Crimping Techniques

The crimping procedure consists of the material to be clamped, the connector body, and a metal crimping sleeve, which is often made of aramid yarns, the cable's strongest element. To optimize your crimping methods, use these suggestions:

To get the optimum crimp and maximum draw force for that assembly, the connection manufacturer specifies the crimp tool for each connector body, die set, crimp sleeve, and crimp force. Using the appropriate tools and components is crucial. Crimped connectors are often textured and rough, which increases the contact surface area. In the overall assembly, such features contribute to the greatest draw force.

Using the incorrect Fiber Crimping Machine might result in a broken cable assembly; the crimp will most likely be too hard or too light. A crimp with too much force might crush the connection. If this structure fails, the glass optical fiber may be destroyed as well. The aramid yarns might pull away if the crimp is too light, reducing the maximum pull power. As a side note, you can utilize the connection manufacturer's suggested fiber curing oven or an automated crimp tool, which provides repeatability and improves process control by reducing operator fatigue.

Follow our Facebook and Twitter for more information about our product.

Fiber Optic Strippers: Know About the Finesse

The core technology of Fiber Cable Stripping Machine is fairly simple. The transmitter uses a blinking LED or laser, and the light travels down the fiber optic link to the receiver, which counts the blinks and translates them into digital or analog electrical impulses. It's straightforward, with one caveat: the wavelengths used in fiber optic communications are higher than those visible to the human eye, thus a technician staring at the tip of a fiber optic connector will not see the blinking signal. 

A fiber that has not been properly prepared cannot be fully inserted into a connector, as there are openings in the back of connectors and splices. At that point, the only choice is to re-strip the fiber to remove the coating, however, the fiber frequently breaks at this stage, so the entire procedure must be repeated. This is one of the primary reasons why, when installing new fiber optic cables/links, there should be a lot of extra fiber cable at each end of the planned connection, as breaking the fibers during the connectorization process is quite common, and technicians should expect to break the fiber strands a couple of times during the manipulation and necessary stripping of the fiber strand.

While technicians must have certain hand skills, using a high-quality Fiber Cable Cutting Machine makes the operation easier and more exact. The common strippers provided with fiber optic tool kits are of the cheap sort, and they frequently need to be modified since the stripping slot may have left the manufacturer with a diameter aperture that cuts into the fiber strand more than necessary, resulting in a broken fiber. In addition, pirated versions of the typically affordable strippers have made their way to our shores.

If a technician notices that they are constantly breaking the fiber when stripping, the Fiber Cable Stripping Machine has to be adjusted. In most situations, fiber strippers' stripping slots may be changed with a tiny Allen wrench. Techs must be careful not to turn the adjustment nut more than a half turn; remember, we're working with microns. A clockwise adjustment widens the slot, while an anticlockwise adjustment tightens it.

Main Source: https://sunmafiber.livejournal.com/